16 Ga Straight Cordless Li-ion Finish Nailer

WHEN YOU NEED PRECISION IN TIGHT SPACES, REACH FOR THE LIGHTWEIGHT PASLDOE CORDLESS FINISHING NAILING SYSTEM.
It gives great maneuverability to place the nail exactly where you want it wherever you’re working: overhead, on ladders or on your knees. Our portable finish nailer, finish nails and fuel cells are designed to work in tandem so you get the job done right, right away.

Powerful precision. Finish right the first time.

Li-ion Battery- drives up to 12,000 nails per charge
Battery Standby Position- Conserves battery power
Lightweight- Only 4.6 pounds for added comfort and control

Where to Buy

Product Information
Related Products
FAQ'S

Product Information

Specs

Model	IM250S-Li
Part #	916000
Nail Type	Use genuine Paslode 16 Ga Straight Finish Nails
Length	1 1/4"- 2 1/2"

Product Documentation

16 Ga Straight Cordless Finish Nailer Warranty

16 Ga Straight Cordless Li-ion Finish Nailer Cleaning Procedure

16 Ga Straight Cordless Li-ion Finish Nailer Operating Manuel

16 Ga Straight Cordless Li-ion Finish Nailer Schematic

VIDEOS

Paslode Intro to Cordless Finish Tools

Paslode Cordless Finish Nailer – Crown Molding

Paslode Cordless Finish Nailer – Door & Window Casing

Cleaning & Maintaining Paslode Cordless Finish Nailer

Paslode Cordless Trim Tool Nail Jam

Paslode Cordless Finish Nailer Fuel

Paslode Cordless Tool Adjusting Depth of Drive

FAQ’s

Are Cordless nailers affected by altitude?

Cordless nailers will not work well above an elevation of 5,000 feet.

Can I use other brands of fuel in my Cordless nailer?

Paslode fuel is formulated for Paslode Cordless nailers. Using other brands of fuel may damage your tool or increase how often it needs serviced.

Can I use something other than Paslode degreaser cleaner to clean my nailer?

Paslode Degreaser Cleaner is specially formulated for Paslode Cordless and pneumatic nailers.. Other products may damage electrical components, plastic parts, and rubber parts. They may also leave a residue which could cause damage to the nailer or injury to the operator of the nailer.

Do fuel cells have a shelf life?

Fuel cells have a “Best Used By” date printed on the bottom of the can. A fuel cell will often work beyond that date, but if a tool starts to work intermittently it could be because the fuel cell has expired. An expired fuel cell has lost enough internal pressure to degrade its performance.

We recommend buying only enough fuel to complete the job. Always check the date on the bottom of the can before purchasing or using a fuel cell to ensure it is not past the best used by date.

Do I need to do anything special to operate the nailers in cold temperatures?

The nailers will perform better in temperatures above 32 degrees Fahrenheit. If you plan on using the nailers below 32F they should be warmed up before use (such as placing them in the cab of a truck while driving to work). Fuel cells can be warmed by placing them in an inside coat pocket. Never place the tool or fuel in the vicinity of a fire or an open heating element.

Do I need to oil my cordless nailer?

Your Cordless nailer comes pre-lubricated from the factory. It is not uncommon to see a small amount of oil that seeped out into the case. Because the fuel contains a small amount of oil, it is not necessary to oil the tool during normal use. The only time the tool should be oiled is after it has been cleaned.

Does Paslode offer a cleaning kit for the Cordless nailers?

Paslode offers Tune Up kits for Cordless Framing and Trim/Finish nailers. The kits contain 12 oz of degreaser cleaner; 10 ml of cordless tool oil; air filter; fuel stem adapter; spark plug; and Tune Up kit instructions. Tune Up kit part numbers:

219305 / Cordless Framing Tune Up Kit for 900420 (IMCT)

219304 / Cordless Trim Tune Up Kit for 900600, 902000, 901000

219377 / Cordless Framing Tune Up Kit for 902200 / 902600 (CF325/CF325Li)

219409 /Cordless Li-ion Trim Nailer Tune up kit 902400

The kits can be purchased at a sales location nearest you or online:

Paslode Parts Site

Paslode Factory Outlet Store

Online Paslode dealers

Does Paslode offer tool repair kits?

Paslode offers the following repair kits:

219305 / Cordless Framing Tune Up Kit for 900420 (IMCT)

219304 / Cordless Trim Tune Up Kit for 900600,902000,901000

219218 / For OLDER Model 5000 Series

219219 / For LATEST Model 5000 Series

219222 / For 3000 Series

219235 / For F350S / 501000

219224 / Trigger Valve Repair Kit for 3000, 4000, 5000 Series, F350S

219245 / Feeder Claw Repair Kit for P275C, F325C, P350C

219379 / Cordless Framing Tune Up Kit for 902200 / 902600 (CF325/CF325Li)

219352 / For PF350S / 502000

The kits can be purchased at a sales location nearest you or online:

Paslode Parts Site
Online Paslode dealers

Does Paslode sell refurbished nailers?

Paslode offers factory-refurbished tools at itwconstructionparts.com. All tools are refurbished by trained Paslode Factory-Service Technicians. Genuine Paslode replacement parts are used where necessary and tools are cleaned to look like new.

Product Offerings include:

Factory Refurbished Cordless and Pneumatic nailers

Replacement Parts

Tune Up Kits and Accessories for Framing and Trim/Finish nailers

Repair Center

How do I find a Paslode Authorized Service Center?

To locate your nearest service location, click on “Service and Retail Locator" at the top of the page and then enter your zip code. Paslode recommends that tools needing service be repaired through your local Factory Authorized Service Network.

How do I order a part online?

Genuine Paslode replacement parts, tune up kits, accessories, and repair service can be purchased online at itwconstructionparts.com.

How do I remove a jammed nail from a Cordless Framing nailer?

First remove the fuel, battery and the remaining nails in the magazine. Using the 5/32 hex key, remove the two screws on either side of the work contact. Next grab hold of the work contact with one hand and the bottom of the magazine with the other. Pull the two away from each other and the magazine will separate from the nose. This will allow the jammed nail to fall out. Inspect the driver blade and push it back up into the tool. Install the two nose screws.

For information click on “Products” at the top of this page, select your nailer and then select the Owner’s Manual PDF Download for your nailer.

How long does it take to charge a battery?

A new battery will take up to 2 hours to fully charge. A partially discharged battery will take between 5 minutes and 2 hours to fully charge depending on the amount of discharge.

How many fasteners can be driven with a fully charged battery?

On average a fully charged battery will drive 4,000 fasteners before needing to be recharged.

The light on the handle of my Cordless nailer is flashing red and green. What does that mean?

The nailer’s electrical system has gone into overload protection. There may be something wrong with the fan motor or the wires going to the fan motor. Remove the battery, fuel and nails. Next remove the cap and grill to inspect the red and black fan motor wires. If the wires are pinched or broken, that may be the problem.

The nailer fires but no nail is being driven. What causes this?

There are several things that could cause a nailer to “blank fire”.

If your tool does not have a lockout, check that you haven’t run out of fasteners

There may be a nail jam preventing the fasteners from moving forward. For information on clearing a nail jam click on “Products” at the top of this page, select your nailer and then select the Owner’s Manual PDF Download for your nailer. This information is typically found toward the back of the manual. You can also check the operations manual that came with your tool.

Cordless nailers may require cleaning. If the tool has driven 10,000 nails or more, it may require cleaning.

What does it mean when the lights on the charger flash red and green?

It is normal for the lights on the charger to flash red/green for up to 20 minutes. The charger is slowly building the charge in the battery until the battery is able to accept the full output of the charger. This protects the battery and increases the life of the battery. If the lights continue to flash red/green after 20 minutes but go to a steady green when the battery is removed, it is likely there is a problem with the battery.

What if my Paslode Cordless Nailer isn’t working?

Check these 6 things to get your nailer back to work.

1. Check fuel cell expiration date

2. Check for empty fuel cell by tapping valve upward against firm object (look for mist)

3. Battery charge – check for green light

4. Dirty filter

5. Nails loaded correctly (never use straight nails)

6. Nail jam – check for operating manual for safety procedures

What is included with a new Paslode Cordless nailer?

A new Cordless nailer includes the following:

Carrying Case

Clear Safety Glasses

Battery Charger

Rechargeable Battery

Hex Key

Owner’s Manual

Tool Reference Guide

What should I use to clean my cordless nailer?

Paslode recommends using Paslode Degreaser Cleaner part number 219086S.

What type of oil should I use after the nailer has been cleaned?

Use only Paslode Cordless Tool Lubricating Oil part number 401482S. It is specially formulated to withstand the high temperatures generated by Cordless nailers. Using other oils can cause the rapid build-up of combustion residue leading to poor nailer performance and more frequent cleanings.

When I fire the Cordless nailer it makes a “POOF” sound. What is causing that?

This can be caused by several things, but a nail jam is the most common. Remove the fuel and battery then clear the jammed nail(s) from the tool. If the driver blade is in the down position the tool will not fire. With the fuel and battery removed from the tool, push the driver blade all the way up into the tool and test the tool.

Where is the serial number located on a Paslode Cordless nailer?

The serial number is engraved on the motor housing of the nailer. It is on the right side (battery compartment side). The easiest way to locate the number is to hold the tool with the battery side up and the nose pointing to your right. Look approximately 1 inch below the “P” on the Paslode label and toward the handle. On the CF325 it is located below the nose of the nailer. The serial number is 9 or more digits long.

Which fuel cell does my Cordless nailer use?

In general, fuel cells with RED labeling are for Framing nailers and fuel cells with YELLOW labeling are for Trim/Finish nailers and Staplers.

Framing Nailer – CF325 Framing nailer (part # 902200) and CF325 Li ion ((902600) => QuickLode Fuel Cells (816008)

Older Framing nailer (part # 900420, 404400, 404600 or 900129) => Red Fuel Cells (part # 816000 or 816050)

16ga Angled Finish nailer (part # 902400) => Quickload Trim fuel (part #816007)

16ga Angled Finish nailer (part # 900600) => Short Yellow Fuel Cells (part # 650039)16ga Straight Finish nailer (part # 902000) => Short Yellow Fuel Cells (part # 650039)

Older model 16ga Straight Finish Nailer (part # 900400 or 900105) => Tall Yellow Fuel Cells (part # 816001)

18ga Brad nailer (part # 901000) => Short Yellow Fuel Cells (part # 650039)

16ga Stapler (part # 900078) => Tall Yellow Fuel Cells (part # 816001)

Will other brands of nails work in my Paslode nailer?

Paslode nailers and fasteners are engineered to work together as a system. Other brands of nails may not be designed or manufactured to the same specifications or quality standards as Paslode. Using nails that do not meet Paslode’s specification may cause damage to the tool and injury to the operator or bystanders, and may void warranty.